Kit i-1500W 24V Wind Turbine & Hybrid Charge Controller & Tower

(No reviews yet) Write a Review
2081/3b -2329-2158
Maximum Power:
24V (AC)
Body Material:
40 dB
Rated Power:
Rated Wind Speed:
Starting Wind Speed:
Min Battery Voltage:
17,5 V
Braking Function (electromagnetic short circuit, wind turbine):
From 29,6 V
10 qmm screw terminals
Max Charging current PV Ampere:
10 A
Max Charging Current Wind Amperes:
55 A
Charging Voltage:
External aluminum cooling fins
LCD with multiple displays Amper, watts, battery voltage, volts.
Dump Load:
1.5 KW brake resistor (2.0 Ohms)
Integrated Manual Stop Switch:
Protection Class:
IP 20 (inside area)
Nominal Battery Voltage:
24 VDC
Max. Input Power of Wind Turbine:
1,5 KW
Max. Input Power of PV Module:
Operating Temperature:
Normal: 20 ~ + 55 ° C / 35 ~ 85% RH Industrial: 30 ~ + 55 ° C / 35 ~ 85% RH
Temperature Compensation:
-4mV ° C / 2V, -35 ° C-- + 80 ° C, accuracy: ± 1 ° C
Recommended Battery Min:
Acid & Gel

Expected release date is Mar 10th 2020

Robust wind generator Original iSTA-Breeze i-1500


Due to the production of glass fiber reinforced plastic, the rotor blades are very durable and stable, at the same time unusually light.

The housing is equipped with cooling fins and is made of high-strength aluminum.

The maintenance-free, sliding contact (without coal) guarantees a good flow of current and thus no twisting of the cable in the mast.

Installation in mast tube by plug connection. Required mast tube inner diameter: 37 mm nominal size!

Further technical data further down in the description.

This product is used successfully 1000 times worldwide! 2 years manufacturer's warranty!


Product description - Charge Controller:

The Wind / Solar Hybrid Charge Controller from IstaBreeze® is an intelligent controller of the wind turbine and solar cells that controls you at the same time. The high-end device can also be used as a monitoring system. It is used to safely and efficiently charge and control your battery with the Wind Generator / Solar Module combination.

With its discreet appearance, simple operation, with integrated protection functions, this device has high efficiency and low no-load losses. This version of the controller will significantly increase the life and stability of the whole system, especially the batteries.

In addition, the control electronics in the control cabinet monitors system voltage and brakes the wind turbine when reaching a max. Overvoltage.


The special features and product information are listed below:

Use of external and high quality (Triacs & Hyper Mosfet), solid state components. Increasing the life of the controller.

Microprocessor controlled charge with integrated voltage and current limiting.

Electromagnetic brake control.

Integrated 3-phase short-circuit switches (brake switch)

Protection against lightning strikes.

Protection against overcharging, deep discharge, short circuit, overload and against incorrect reverse polarity.

Integrated display.

The generator is automatically braked gently when the battery is full, modern braking system with external load resistance (Dump Load) to avoid immediate blockage of the turbine. Increasing the life of the stator.




  • Material: Composite 
  • Lenght of per blade: 107 cm
  • Weight of per blade: 650 g
  • Rotor Diamater: 225 cm



4 meters IstaBreeze® TOWER for wind generator i-700 to i-2000,

(our WindSafe models require an adapter)

It has never been so easy to install a wind generator.

With the IstaBreeze® Tower it is possible to build a wind generator in a few minutes.

The folding system simplifies the whole process.

During maintenance, only a few screws are released and the tower can be folded for maintenance.

The mast can be extended by a maximum of 2 meters!

Dowels and screws for the floor (concrete floor) is still needed !!

Diameter of the mast is: 60 mm

Inner hole, plug connection Wind generator IstaBreeze® .......... 37 mm


Optional The vibration damper for the wind generators i-500- L-500 and i-700 to i-2000, reduces the transmission of structure-borne noise from the wind generator into the mast and thus possibly into the house. The retrofit is very simple, because the body silencer has the same dimensions as the wind generator, it must only be inserted between them and screwed with matching screws on the mast and the wind generator. (Not for WindSafe models)

The vibration damper is compatible with our original IstaBreeze® masts 15kg and 40kg.





2 Year Warranty